Preparation of two-dimensional molybdenum disulfide for NO2 detection at room temperature

In this work, the two-dimensional MoS₂ film was prepared by sulfuring the molybdenum atomic layer on SiO₂/Si substrate. The reaction temperature, heating rate, holding time and carrier gas flow rate were investigated comprehensively. The quality of MoS₂ film was characterized by optical microscopy, atomic force microscopy, Raman and photoluminescence spectroscopy. The characterization results showed that the optimum synthesis parameters were heating rate of 25 °C/min, reaction temperature of 750 °C, holding time of 30 min and carrier gas velocity of 100 sccm. The MoS₂ gas sensor was fabricated and its gas sensing performance was tested. The test results indicated that the sensor had a good response to both reducing gas (NH₃) and oxidizing gas (NO₂) at room temperature. The sensitivity to 100 ppm of NO₂ was 31.3%, and the response/recovery times were 4 s and 5 s, respectively. In addition, the limit of detection could be as low as 1 ppm. This work helps us to develop low power and integrable room temperature NO₂ sensors.     

Investigation of melamine and DOPO-derived flame retardants for the bioplastic cellulose acetate

In order to identify suitable flame retardant additives for the eco-friendly polymer cellulose acetate (CA), high-melting derivatives of the known flame retardant 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) were combined with the thermoplastic CA and the combustion properties were tested. CA mixtures with bis-phosphonamidates (EDA-DOPO and PIP-DOPO) showed distinct flame retardation effects and a reduction of peak heat release rates (PHRR) by up to 18%. CA mixtures with MDOP, a melamine salt of DOPA (an oxidation product of DOPO), also showed considerable effects and a reduction of PHRR by up to 27%. While producing more smoke than pure CA and CA plus melamine, owing to its aromatic component, MDOP was superior to the CA mixtures with DOPO, EDA-DOPO and PIP-DOPO in this regard. The mixture of CA with melamine gave rise to a distinctly reduced formation of toxic CO and smoke when compared with pure CA. Thus, these additives can be considered for future applications of CA-based polymers with enhanced flame protection.     

Architectural control of polystyrene physical properties using branched anionic polymerization initiated at ambient temperature

Ambient temperature-initiated anionic polymerization has generated branched polystyrenes of varying molecular weights and architectures by inclusion of a distyryl branching comonomer into a conventional sec-Butylithium-initiated polymerization of styrene. Primary chain length control within the branched polymers, and restriction of the branching points to varying segments of the primary chains, led to variations of glass transition temperature with no direct correlation to the branched polymer molecular weight but a strong relationship to the length of individual chains comprising the branched macromolecules.     

Photoinitiated polymerization of methacrylates comprising phenyl moieties

Investigation of photopolymerization kinetics of 4-(4-methacryloyloxyphenyl)-butan-2-one (1) in comparison with 2-phenoxyethyl methacrylate (2) and phenyl methacrylate (3) using a UV-LED emitting at 395 nm shows significantly faster polymerization of 1 compared to both 2 and 3 at 40°C. Vitrification affects photopolymerization kinetics of all methacrylates under investigation. Interestingly, quantitative final conversion is observed during photoinitiated polymerization of 1 and 2 whereas 3 shows limited conversion at about 80%. Furthermore, higher degree of polymerization is obtained by photoinitiated polymerization of 1 compared to 2 and 3. This shows that the 3-oxobutyl substituent at the phenyl ring of 1 significantly affects both polymerization kinetics and final conversion of the photoinitiated polymerization. Moreover, an additional higher molecular weight fraction is observed in case of polymerization of 1 at 85°C that is above the glass transition temperature of the polymer formed during photoinitiated polymerization. As a thermal polymerization at 85°C in the absence of light results in a high molecular weight polymer as well, an additional thermal process may be discussed as reason for the higher molecular weight polymer fraction in case of the photopolymer made at 85°C.     

Noncovalent Intermolecular Interaction in Cofacially Stacked 24π Antiaromatic Hexaphyrin Dimer

π–π Stacking is omnipresent not only in nature but in a wide variety of practical fields applied to our lives. Because of its importance in a performance of natural and artificial systems, such as light harvesting system and working layer in device, many researchers have put intensive effort into identifying its underlying nature. However, for the case of π–π stacked systems composed of antiaromatic units, the understanding of the fundamental mechanisms is still unclear. Herein, we synthesized a new type of planar β,β’-phenylene-bridged hexaphyrin (1.0.1.0.1.0), referred as naphthorosarin which possesses the 24π-electron conjugated pathway. Especially, the corresponding antiaromatic porphyrinoid shows the unique property to form dimeric species adopting the face-to-face geometry which is unprecedented in cases of known annulated naphthorosarins. In order to elucidate the intriguing properties derived from the stacked dimer, the current study focuses on the experimental support to rationalize the observed π–π interactions between the two subunits.     

Pitch-Based Laminated Carbon Formed by Pressure Driving at Low Temperature as High-Capacity Anodes for Lithium Energy Storage Systems

Pitch has been used to prepare electrodes by high-temperature heat treatments for supercapacitors, lithium-ion batteries, on account of its rich aromatic ring structure. Here, the toluene-soluble component of pitch is used to prepare a kind of laminated carbon. This was realized by a template-free synthesis at low temperature with the addition of pressure. The toluene-soluble component has a small molecular weight, which makes the thermal deformation ability stronger and then enhances the orientation of the carbon layer with the help of pressure. The prepared anode exhibits a splendid electrochemical performance compared with the traditional graphite anode. A high stable capacity of approximately 550 mAh g⁻¹ at 50 mA g⁻¹, which is much higher than graphite (372 mAh g⁻¹), is obtained. Also, when the current density is up to 2 A g⁻¹, the capacity is about 150 mAh g⁻¹. Surprisingly, it also delivers a superior cycling performance. And when used as the anode/cathode electrode for lithium-ion capacitors, a high energy density can be obtained. The present work offers an opportunity to utilize the pitch source in lithium energy storage with promising cycle life, high energy/power density, and low cost.     

Ignition of hydrogen–oxygen and stoichiometric hydrogen–methane–oxygen mixtures on hot wires at low pressures

1. Download : Download high-res image (104KB)
2. Download : Download full-size image

     

室温铁磁性Sr3YCo4O10.5+δ多晶有序化的烧结工艺及电磁性能

采用固相反应法制备了不同烧结温度(950~1 180 ℃)、烧结时间、烧结次数共7种工艺的Sr₃YCo₄O_10.5+δ多晶块材,通过热分析、XRD、SEM确定了有序化相变和最佳烧结工艺(1 180 ℃/24 h+1 180 ℃/24 h),并研究了多晶的电磁性能。结果表明,964 ℃完全晶化的四方相Sr₃YCo₄O_10.5在1 042 ℃吸氧(δ)完成有序化,生成Sr₃YCo₄O_10.5+δ,而1 100 ℃和1 180 ℃烧结的样品均出现(103)、(215)超结构峰,验证了其结构的有序性。块材均呈半导体电输运行为,二次烧结晶格完整性提高,晶粒长大,300 K时电阻率仅为0.06 Ω·cm,居里温度(T_c)~335 K,零场冷曲线(ZFC)上的Hopkinson峰源于低温时被冻结的磁矩随温度升高转向磁场方向,磁化强度在298 K达到最大,随后受热扰动的影响减小。室温铁磁性源于有序结构导致的中自旋或高自旋态Co³⁺的e_g轨道有序。     

6英寸低位错锗单晶生长热场设计

锗片作为衬底材料已在空间太阳电池领域得到广泛的应用,新型锗基空间太阳能电池对锗片的需求由4英寸(1英寸=2.54 cm)提高到6英寸后,低位错锗单晶的生长难度增大。本文设计开发了一种适用于直拉法生长大尺寸、低位错锗单晶的双加热器热场系统,模拟研究了不同形状主加热器的热场分布,从而得到最优的热场环境。研究发现:渐变长度为L/h=1/2、渐变率α为65°的渐变型主加热器热场结构能够获得最佳的热场分布,有利于低位错单晶的生长。经验证,生长的锗单晶热应力较低,位错密度在310～450 cm^-2范围内。     

Optimisation of the ultrasound-assisted extraction of betalains and polyphenols from Amaranthus hypochondriacus var. Nutrisol

The present study optimised the ultrasound-assisted extraction (UAE) of bioactive compounds from Amaranthus hypochondriacus var. Nutrisol. Influence of temperature (25.86–54.14 °C) and ultrasonic power densities (UPD) (76.01–273.99 mW/mL) on total betalains (BT), betacyanins (BC), betaxanthins (BX), total polyphenols (TP), antioxidant activity (AA), colour parameters (L*, a*, and b*), amaranthine (A), and isoamaranthine (IA) were evaluated using response surface methodology. Moreover, betalain extraction kinetics and mass transfer coefficients (K_La) were determined for each experimental condition. BT, BC, BX, TP, AA, b*, K_La, and A were significantly affected (p < 0.05) by temperature extraction and UPD, whereas L*, a*, and IA were only affected (p < 0.05) by temperature. All response models were significantly validated with regression coefficients (R²) ranging from 87.46 to 99.29%. BT, A, IA, and K_La in UAE were 1.38, 1.65, 1.50, and 29.93 times higher than determined using conventional extraction, respectively. Optimal UAE conditions were obtained at 41.80 °C and 188.84 mW/mL using the desired function methodology. Under these conditions, the experimental values for BC, BX, BT, TP, AA, L*, a*, b*, K_La, A, and IA were closely related to the predicted values, indicating the suitability of the developed quadratic models. This study proposes a simple and efficient UAE method to obtain betalains and polyphenols with high antioxidant activity, which can be used in several applications within the food industry.